Created with Voloom

Slot together side table

A 400 × 400 mm side table, 450 mm tall, cut from 18 mm ply: two splayed A-frame end panels with arched feet, tabbed into the top, and a lower shelf that lock…

Furniture leg riser

Tapered square furniture leg riser, hollow underneath with crossing ribs, a top pocket for the leg and a chamfered bottom edge.

Floating shelf bracket

L-shaped floating shelf bracket with a triangular gusset, two countersunk wall screw holes and two 4 mm holes in the arm.

Broom mop holder

Wall-mounted broom and mop holder: a 70x50x6 back plate with two 4 mm screw holes and a 30 mm tall C-clip with a front opening and flexible arms that grips h…

Door stop wedge

A 130 x 45 mm door stop wedge rising from 3 mm to 28 mm, with triangular grip ridges on the slope, a lanyard hole near the tall end and a slightly dished und…

Coat hook rail

A 300x40x10 mm wall rail with three evenly spaced ball-ended hooks and three countersunk screw holes.

Gridfinity screw organizer

Gridfinity screw organizer bin with divider grooves in the long walls, magnet and screw holes under the feet, and three separate removable divider plates tha…

Gridfinity scissors holder

2x1 Gridfinity holder with magnet holes: a 50 mm block with two angled 4x70 mm scissor-blade slots and a round craft-knife cup.

Gridfinity hex key holder

2x1 Gridfinity bin with seven hex sockets for 1.5 to 6 mm keys (0.3 mm oversize, 18 mm deep), raised size labels and a magnet base.

Gridfinity drawer

Gridfinity drawer built as a 3 x 4 gridfinity_bin, 6 units (42 mm) tall, with top flanges that ride on two separate 180 mm desk-mount rails and an optional 4…

Gridfinity 1×1 bin

1x1 Gridfinity bin, 6 units tall, with four 6.1 mm magnet pockets, an optional front label tab and an optional separate press-fit lid.

Gridfinity 2×1 bin

2x1 Gridfinity bin, 3 units tall, with a stacking lip, magnet pockets, a front label tab and a separate flat lid that seats in the lip.

Modular 21700 battery cell spacer tile

Four staggered-honeycomb 21700 cell holder tiles laid out in a 2x2 lattice, each tile now 4 columns of 5 cells, with dovetail tabs on its right and top edges…

Mudular 21700 battery cell spacer tile

4x4 honeycomb 21700 cell holder tile with thick 5.5 mm walls and half-cell cradles on all four edges. Dovetail tabs on its right edge (three) and top edge (f…

18650 holder 4x

Four-cell 18650 holder with round open-top cradles between two slotted end walls and a bottom mounting tab with a 3 mm hole on each end.

Shop vac hose adapter

Stepped tube adapter: a 60 mm long, 32 mm OD hose spigot, a 40 mm cone, then a 50 mm long socket with 58 mm inner diameter, 2.5 mm walls and a slight frictio…

C clamp

C-clamp with a threaded frame arm, a screw whose cylindrical head now has a rounded top edge above the cross handle, and a separate clamping pad. The frame's…

Bambu poop chute bucket

Two-part waste chute: a hollow 70x40x35 chute with a 28x18 hooked inlet lip and dovetail rails underneath, plus a separate 90x70x80 bucket whose lid has matc…

IKEA Skadis tray

A boxy open tray whose two rectangular side walls are hooked brackets for an IKEA Skadis board, with finger-jointed bottom and front and a back wall between…

IKEA Skådis organizer tray with dividers

Shorter open tray with dividers, hung on a Skadis board by two hooked side brackets that curve down to a low front.

IKEA Skådis bin

An open tray on two hooked side brackets that hang on an IKEA Skadis board, with a floor, a front wall and a back wall.

skadis bin

IKEA Skadis bin

A bin that hooks straight into your Skadis board with no clips. Three cells wide to start, 120 mm, with a curved front so you can reach in.

Skådis thread spools holder

Hang-on comb plates for an IKEA Skadis board; each plate has hooks that drop into the pegboard slots and sloped blade pegs with rounded corners that carry th…

IKEA Skådis modem cradle for coda56

IKEA Skådis hook bracket: a 5 mm back plate with eight drop-in hooks, a 173 mm wide open-top cradle for a Hitron CODA 56 modem, and two diagonal corner lips…

name sign

Laser cut name sign

Laser cut name sign as a parametric cut file. Set the stock and size, then download the SVG or DXF.

Rover chassis

3D-printable four-motor rover chassis: a 180x120x4 plate with four half-saddles at the corners, BTS7960 and ESP32 standoff pads, a 150x60 battery tray with s…

Pipped die

A 22 mm die with 3 mm rounded edges and 1 to 6 recessed pips per face, each 0.8 mm deep.

Three arm fidget spinner

Three-arm fidget spinner, 7 mm thick, 75 mm tip to tip, shown assembled: two 22 mm finger caps sit on either face of the centre bearing seat and screw into e…

Castle dice tower

Castle-style dice tower: four round corner turrets, battlements (merlons) around the open top and arrow-slit windows, with the same internal baffles, front e…

Treasure chest

Treasure chest with a hollow base, a barrel-vault hollow lid, metal straps, and a lock plate with a hasp.

opengrid hook

openGrid hook

openGrid hook as a parametric solid. Change a size, then download the STL.

opengrid bit holder

openGrid bit holder

openGrid bit holder as a parametric solid. Change a size, then download the STL.

opengrid cable organizer

openGrid cable hook

openGrid cable hook as a parametric solid. Change a size, then download the STL.

opengrid headphone holder

openGrid headphone hook

openGrid headphone hook as a parametric solid. Change a size, then download the STL.

opengrid screwdriver holder

openGrid screwdriver holder

openGrid screwdriver holder as a parametric solid. Change a size, then download the STL.

opengrid cable management

openGrid cable channel

openGrid cable channel as a parametric solid. Change a size, then download the STL.

Raspberry Pi 5 snap fit case

Two parts: a base with standoffs and port cutouts, and a snap-fit lid with an engraved ring and logo. The back wall carries engraved text.

Raspberry Pi 4 snap fit case

Two parts: a base with standoffs and port cutouts, and a snap-fit lid with a logo engraved in a ring.

Rover chassis

3D-printable four-motor rover chassis: a 180x120x4 plate with four half-saddles at the corners, BTS7960 and ESP32 standoff pads, a 150x60 battery tray with s…

Arduino nano case

Two-part Arduino Nano case shown assembled: the snap-on lid sits closed on the base with its lip inside the cavity. The base has a USB end cut-out and side s…

Heltec v3 meshtastic case

Two-part Heltec WiFi LoRa 32 V3 Meshtastic case shown assembled, sized to the real 50.8 x 25.4 mm board. Posts sit between the two pin-header rows, the USB-C…

Arduino Uno Q case

Two-part enclosure for the Arduino UNO Q (Uno form factor, 68.6 x 53.3 mm): a base tray with four standoffs and a USB-C opening, plus a lid with a locating l…

Cable drag chain

Five identical separate drag-chain links, 15x10 mm inside and 20 mm long, snap-pinned at the sides and posed in a gentle curve, with a top bar and an open to…

Planetary gearbox

Single-stage planetary gearbox: sun gear, three planets on a pinned carrier, and an internal ring gear, with a 4.67:1 reduction when the ring is fixed and th…

Corner hand crank winch

Corner-mounted hand-crank winch: an L-flanged frame with a chamfered mounting corner, two bearing cheeks, a flanged spool fixed to an axle, a crank arm, and…

Archimedean screw

Single-piece Archimedean screw: 12 mm core with a right-hand rectangular flight (36 mm major, 18 mm pitch) and 8 mm smooth journals on both ends.

Jack saddle pad

Bottle jack saddle pad: 55 mm disc with a raised locating ring on top, a 28 mm piston boss underneath and four drain holes on a 36 mm bolt circle.

Bevel gear pair 90

Two meshing 90-degree bevel gears (16T and 32T, module 2) sharing a common apex at the origin, each with a 6 mm x 15 mm integral shaft stub.

Christmas village

Three tea-light houses (60, 80 and 100 mm tall) with finger-jointed walls, tabbed pitched roofs, glowing windows, engraved roof tiles and door planks, and an…

Flat pack christmas tree

Two identical tiered tree silhouettes with a star on top, slotted together at 90° with a cross joint so the tree stands on its own.

Christmas ornament

Round 75 mm Christmas ornament with raised rim, raised editable name, raised star and a flat-backed hanging loop.

Personalised bauble ornament

80 mm round plywood bauble with a scalloped crown, 6 mm hanging hole, engraved script name and a ring of snowflake cutouts.

Christmas ornament set

Six flat 3 mm ornaments (star, tree, bauble, bell, snowflake, gift) laid out on one sheet, each with a 5 mm hanging hole, cutout decoration and an engraved d…

tea light holder

Laser cut tea light holder

Laser cut tea light holder as a parametric cut file. Set the stock and size, then download the SVG or DXF.

Pixel 11 pro bumper

Open-back bumper case for the Google Pixel 11 Pro that wraps the edges, with front and back retaining lips and cutouts for the USB-C port and side buttons.

Pixel 11 pro wall mount

Wall-mounted cradle for a Google Pixel 11 Pro with a back plate, side walls, a bottom shelf with a front retaining lip, and a cable slot through the shelf an…

Iphone 18 pro max case

Snap-on phone case for a large 6.9-inch class phone, with a screen lip, a camera cutout, side button slots, and USB-C and speaker openings.

Pixel 7 case

Snap-on phone case for a Pixel 7 with a front retaining lip, a shallow back recess framed by a raised perimeter rim, a camera bar window, side button slots a…

Samsung Galaxy A07 phone case

One snap-fit part with retaining lips, a camera window, a side button slot and a port slot at the bottom.

Phone stand 60°

Two profiled side plates with a front lip and a 60° back slope, tied together by three tabbed cross bars, one of which has a cable window.

multiboard hook

Multiboard hook

Multiboard hook as a parametric solid. Change a size, then download the STL.

multiboard cable management

Multiboard cable channel

Multiboard cable channel as a parametric solid. Change a size, then download the STL.

multiboard bit holder

Multiboard bit holder

Multiboard bit holder as a parametric solid. Change a size, then download the STL.

multiboard gridfinity

Multiboard Gridfinity shelf

Multiboard Gridfinity shelf as a parametric solid. Change a size, then download the STL.

multiboard bin

Multiboard bin

Multiboard bin as a parametric solid. Change a size, then download the STL.

honeycomb storage wall bin

Honeycomb Storage Wall bin

A bin that pushes straight into your honeycomb wall on hex plugs, with a curved front you can reach into.

Raspberry pi 3 case

Two-piece Raspberry Pi 3 Model B case with rounded outline, board standoffs, port and SD cutouts, and a vented snap-fit lid.

Phone stand

Desktop phone stand on a shield-shaped base (wide rounded back, sweeping curved shoulders, pointed front tip) with a front lip, a backward-leaning backrest a…

Phone stand

Desk phone stand with a flat base, a backward-leaning backrest, a front lip that holds the phone's bottom edge, and an optional cable slot.

A4 lightbox

Single-piece hollow lightbox with a top slot for an A4 cardboard sheet resting on full-height side lips, an integrated closed back, and a cable socket in the…

Desk cable clip

Printable cable clip with a C-slot snap channel and an adhesive-pad recess, plus an optional insert lid that turns it into a screw mount.

Bag clip

Two-jaw friction bag clip with sealing rib on one jaw, a finger tab on each jaw, five alternating 6 mm knuckles and a separate 4 mm hinge pin.