Projects for the home

Slot together side table

A 400 × 400 mm side table, 450 mm tall, cut from 18 mm ply: two splayed A-frame end panels with arched feet, tabbed into the top, and a lower shelf that lock…

Furniture leg riser

Tapered square furniture leg riser, hollow underneath with crossing ribs, a top pocket for the leg and a chamfered bottom edge.

Floating shelf bracket

L-shaped floating shelf bracket with a triangular gusset, two countersunk wall screw holes and two 4 mm holes in the arm.

Broom mop holder

Wall-mounted broom and mop holder: a 70x50x6 back plate with two 4 mm screw holes and a 30 mm tall C-clip with a front opening and flexible arms that grips h…

Door stop wedge

A 130 x 45 mm door stop wedge rising from 3 mm to 28 mm, with triangular grip ridges on the slope, a lanyard hole near the tall end and a slightly dished und…

Coat hook rail

A 300x40x10 mm wall rail with three evenly spaced ball-ended hooks and three countersunk screw holes.

Toilet paper holder

Wall-mounted toilet paper holder: 90x60x6 plate with two countersunk screw holes, a 150 mm long 25 mm diameter arm, and a raised lip at the free tip.

Bike wall hook

Wall-mounted bike hook: a vertical 40x90x8 back plate with two countersunk 5 mm screw holes 60 mm apart, a rounded J-shaped arm 30 wide that projects 110 mm…

Shower razor holder

Wall-mounted shower razor holder with a screw-mounted back plate, a front-slotted drainage shelf and a front lip.

SNES cartridge tray

One-piece SNES cartridge stand with an editable 'cartridges' count: a floor, a front panel leaning back at the same tilt as the fins, equal-height fins leani…

Low poly hanging planter

Sleek faceted hanging planter: one tapered hexagonal body with a flush-topped open cavity, three small flat hex tabs for cords, and a drain hole.

Ashtray

Round ashtray with a deep bowl, four cigarette-rest scoops in the rim and optional feet.

Coral ceramic mug

Tapered open-top ceramic mug with a thin wall, a midspan station, and a C-shaped side handle on the +X side.

Drawer cabinet

Finger-jointed carcass with a back and two tabbed shelves, holding three sliding finger-jointed drawers with hand slots.

Mug

Cylindrical mug with a hollow cavity, a thick floor and a rounded C-shaped side handle.

Glueless desk organizer

Open-top desk tray with finger-jointed walls and two crossing dividers; every joint is a mechanical finger, tab or cross-slot, so it assembles without glue.

Two drawer cabinet

Small carcass with a middle shelf and two finger-jointed open-top box drawers stacked in two bays.

Shot glass

Tapered shot glass with a thick solid base, a chamfered underside edge, a shallow recess under the base for a flat standing ring, thin walls and an open rim…

Plastic wine glass

Clear stemmed wine goblet: a solid of revolution with a thin flat foot, slender stem with a small bead, a softly filleted stem-to-bowl junction, and an open…

Chair - Pointy

Flat-pack side chair with two angular side frames (forward-splayed tapered front legs, a gabled apron and a single raked back post), a seat panel and two che…

A stool

Round plywood stool: a disc seat held by two interlocking leg frames whose legs splay outward, tabbed up through the seat.

Box with a hinged lift lid

Five parts: a bin, a hinged lid that follows its curved front, and a foot pedal that lifts the lid through a link bar and push rod.

Finger jointed desktop organizer

Finger-jointed desktop organizer with a front-open carcass, two tabbed shelves and three open-top drawers, each with a finger-pull slot.

Pitched roof birdhouse

Finger-jointed birdhouse with a front-overhanging pitched roof, a 32 mm entrance hole, a flat perch with a rounded end, and a tall back plate with a hanging…

Cross leg stool

Round stool with two cross-slotted X legs, a ring at the feet tying them together, and a round seat tabbed into the leg tops.

Round lantern

A two-storey round lantern with a double candle door (two leaves, each hinged on top and bottom pins at its outer side), a diamond cross-hatch lattice with s…

Workstation desk

A wide flat-pack desk on two tapered, splayed inverted-U leg frames with the desk top resting between them, an upper bracket pressed against the underside of…

Chair - Rounded

A taller, sleeker flat-pack chair with tapered side frames and a backrest reclined at an angle: the front legs splay forward and narrow toward the foot, and…

Under desk cable tray

Under-desk U-channel cable tray with open ends and outward top lips, two separate slotted L-bracket clips that hook under the lips, and optional friction-fit…

Self draining soap dish

A 120x80x18 mm soap dish with a 4° floor sloping to an open front, six ribs, 3 mm side and back walls, four 3 mm feet at the corners, and a separate drip tra…

Parametric box with lid

Two-part storage box (100x70x50 inside, 1.6 mm walls) with a recessed 4 mm lid, optional snap hook and slot on the front long side, and optional two-knuckle…

Cable comb

Flat cable comb with eight open-top slots and optional mounting holes at each end.

Locking multi cable clip

Four-cable locking clip: a base with four 7.5 mm channels, a separate snap-on lid with 1.2 mm latch barbs shown lifted above the base, and optional 4 mm end…

Mouse bungee

Weighted disc base with a coin pocket underneath, a vertical arm and a C-clip on top that snaps a mouse cable in.

Controller stand

Two-piece game-controller stand: a 90x70 base plate and a separate 70 mm-wide saddle with an 18 mm channel, leaned back 12 degrees and resting on the base.

Laptop stand

Two sloped 12 degree risers with front lips and a separate 220 mm spreader that slots into 4 mm mortises; three printed parts.

Drawer organizer set

Three separate open drawer trays (160x80, 160x40, 80x80 mm), 1.2 mm walls, 35 mm tall, each with a 1 mm stacking rim, laid out side by side with a small gap.

Toothbrush holder

Hollow toothbrush cup with an 8 mm floor drain and a separate drop-in insert with four 12 mm brush holes.

Wall key hook

180x20x10 wall key rail with a 4 mm dovetail, two 4 mm screw slots and four separate 12 mm wide J-hooks that slide on the dovetail.

Remote control holder

Desk remote caddy block with three 48x28 mm slots and one 18x18 mm slot, each with a 1.6 mm floor, plus finger notches in the front wall so the cavities read…

Spice drawer insert

Two separate 200x50 mm wedge-shaped spice rack rows, each with four 45 mm jar pockets 12 mm deep, tilted 15 degrees back so labels face up and out.

Coffee pod holder

Rectangular coffee-pod tray with a 4 x 3 grid of round 38 mm pockets, 16 mm deep, separated by 1.6 mm walls, on a 1.6 mm floor.

Steam Deck stand

Steam Deck stand: 110x80 base with a dovetail groove and a separate 128 mm wide yoke with an 18 mm slot leaning at 65 degrees and a 12 mm cable notch.

Switch stand

Low desk kickstand block with a 12 mm slot leaning the console at 70 degrees and a cable notch out the back.

Socket organizer rail

Flat rail with twelve 3/8 in drive posts 12 mm tall, a label recess under each post for sizes 10 to 21 mm, and two 5 mm hang holes.

plasma cut sign

Plasma cut name sign

Plasma cut name sign as a parametric cut file. Set the stock and size, then download the SVG or DXF.

house number sign

House number sign

House number sign as a parametric cut file. Set the stock and size, then download the SVG or DXF.

laser cut organizer

Laser cut desk organizer

Laser cut desk organizer as a parametric cut file. Set the stock and size, then download the SVG or DXF.

laser cut lamp

Laser cut lamp

Laser cut lamp as a parametric cut file. Set the stock and size, then download the SVG or DXF.

tea light holder

Laser cut tea light holder

Laser cut tea light holder as a parametric cut file. Set the stock and size, then download the SVG or DXF.

cnc box

CNC box with lid

CNC box with lid as a parametric cut file. Set the stock and size, then download the SVG or DXF.