17 designs
3D printable tool holders and workshop prints
Clamps, bench dogs, bit indexes, parts trays and printer helpers for the workshop. Fit them to your tools before you print.
ModelForkModular 21700 battery cell spacer tile
Four staggered-honeycomb 21700 cell holder tiles laid out in a 2x2 lattice, each tile now 4 columns of 5 cells, with dovetail tabs on its right and top edges…
ModelForkMudular 21700 battery cell spacer tile
4x4 honeycomb 21700 cell holder tile with thick 5.5 mm walls and half-cell cradles on all four edges. Dovetail tabs on its right edge (three) and top edge (f…
ModelFork18650 holder 4x
Four-cell 18650 holder with round open-top cradles between two slotted end walls and a bottom mounting tab with a 3 mm hole on each end.
ModelForkShop vac hose adapter
Stepped tube adapter: a 60 mm long, 32 mm OD hose spigot, a 40 mm cone, then a 50 mm long socket with 58 mm inner diameter, 2.5 mm walls and a slight frictio…
ModelForkBambu poop chute bucket
Two-part waste chute: a hollow 70x40x35 chute with a 28x18 hooked inlet lip and dovetail rails underneath, plus a separate 90x70x80 bucket whose lid has matc…
ModelForkFilament spool holder
Two open A-frame spool stands with 8.2 mm axle holes at 50 mm height, optional 608 bearing seats on the inner faces, and a separate 8 mm x 100 mm axle.
ModelForkParametric box with lid
Two-part storage box (100x70x50 inside, 1.6 mm walls) with a recessed 4 mm lid, optional snap hook and slot on the front long side, and optional two-knuckle…
ModelForkUnder desk headphone hook
Under-desk headphone hook: a C-clamp for 15-30 mm desk tops with a printed M10 screw and 20 mm knurled knob, and a 60 mm J-hook bolted to the clamp spine.
ModelForkPTFE tube clip
Small PTFE tube clip block with a snap-in C-slot channel and a 6 mm screw hole.
ModelForkFilament guide arm
A 120x16x8 filament-guide arm with a 6 mm slot clamp at one end and a ball stud at the other, plus a separate 8 mm eyelet with a 2.4 mm bore that snaps onto…
ModelForkPrinter purge bin
Open-top 100x70x60 purge bin with 1.2 mm walls and a rear J-hook with an 8 mm lip that hangs over a 6 mm rail or 2020 extrusion lip.
ModelForkDrill bit index
Drill-bit index block with 19 blind holes (1-10 mm in 0.5 mm steps, +0.2 mm clearance) in two rows, raised label bars, and an optional sliding lid in side ra…
ModelForkMagnetic parts tray
Open parts tray 120x80x15 with 2 mm walls and 8 mm rounded corners, with optional four 20 mm magnet pockets under the floor.
ModelForkCorner clamp
90° L-frame corner clamp, 80x80x20 with a 40 mm opening, a printed M10 screw through the jaw and a ball-swivel pad on the tip.
ModelForkTape measure holster
Open-top holster with an 82x42x70 mm pocket for a 5 m tape measure and a back-mounted belt loop that takes a 40x4 mm belt.
About Tools
Workshop prints have to fit the tool in your hand: a drill bit set, a tape measure, a PTFE tube. Each design here exposes those sizes as parameters.
Fork one, enter your measurements, and download a print-ready STL or a STEP for further CAD work.