IKEA Skådis accessories to 3D print

IKEA Skadis tray

A boxy open tray whose two rectangular side walls are hooked brackets for an IKEA Skadis board, with finger-jointed bottom and front and a back wall between…

IKEA Skådis organizer tray with dividers

Shorter open tray with dividers, hung on a Skadis board by two hooked side brackets that curve down to a low front.

IKEA Skådis bin

An open tray on two hooked side brackets that hang on an IKEA Skadis board, with a floor, a front wall and a back wall.

skadis bin

IKEA Skadis bin

A bin that hooks straight into your Skadis board with no clips. Three cells wide to start, 120 mm, with a curved front so you can reach in.

Skådis thread spools holder

Hang-on comb plates for an IKEA Skadis board; each plate has hooks that drop into the pegboard slots and sloped blade pegs with rounded corners that carry th…

IKEA Skådis modem cradle for coda56

IKEA Skådis hook bracket: a 5 mm back plate with eight drop-in hooks, a 173 mm wide open-top cradle for a Hitron CODA 56 modem, and two diagonal corner lips…

IKEA Skådis phone holder

IKEA Skådis pegboard phone holder with two hook pegs on 40 mm centres and a tilted 78 x 18 mm phone slot at 65 degrees with a 6 mm front lip and an 8 mm cabl…

IKEA Skådis tray

Open-top wall tray, 120x70x40 mm inside with 1.6 mm walls, two IKEA Skådis hook pegs on 40 mm centres, a 3x3 grid of 4 mm drain holes and an optional centre…

IKEA Skådis hook

IKEA Skådis pegboard hook: two 5 mm pegs on 40 mm centres, a 4 mm back plate and a 12 mm wide J-hook projecting 35 mm, with an optional second hook 20 mm lower.

IKEA Skådis headphone holder

IKEA Skådis headphone holder: two pegs on 40 mm centres, a 90 mm wide R55 U-cradle with 3 mm walls and 6 mm lips, and an optional side cable hook.

IKEA Skådis screwdriver holder

Two-piece IKEA Skådis screwdriver holder for printing, now stood upright as it hangs: a vertical back plate with four rounded J-pegs and two swept supports f…

IKEA Skådis shelf

IKEA Skådis pegboard shelf: 160x80x4 plate with two 5 mm mounting holes on 80 mm centres, a 16 mm rear riser, two drop-in J-pegs on 80 mm centres and an opti…

IKEA Skådis plier holder

IKEA Skådis plier holder: a 100 mm bar with five 12x8 mm slots, 8 mm deep on 18 mm pitch, cut into its open front face, on a 4 mm back plate with two drop-in…

IKEA Skådis cable hook

IKEA Skådis pegboard cable hook with a 4 mm back plate, two drop-in pegs on 40 mm centres, and three 8 mm wide J-hooks in a vertical row 18 mm apart.

IKEA Skådis tablet holder

IKEA Skådis tablet holder: 4 hook pegs on an 80x40 pattern, a 180x18 slot open at the top of the cradle and tilted 70 degrees, a 10 mm front lip and a 12 mm…

IKEA Skådis spray can holder

IKEA Skådis spray-can holder, shown standing upright: a back plate as wide as the semicircles' straight side, with two J-pegs on the wall side. A semicircula…