skadis bin
Prompt that made this
IKEA Skadis bin, 3 cells wide and 2 cells tall, 50 mm deep, 1.6 mm walls, front wall lowered 18 mm with a smooth curve, 5 mm rounded front corners, no dividers. Put cells_x, cells_z, depth, front, dividers_x, corner, drain and scoop in the parameters, and a label choice, as on the other wall-system bins.
Made in Voloom from the prompt under the model. Sign in to download the STL, or fork it so every size on the right becomes editable — without spending a prompt.
Independent third-party part. Not affiliated with, endorsed by, or sponsored by IKEA.
Why this one
IKEA's own Skadis containers come in a few fixed sizes. Printing your own means you get the size for what you're actually storing, whether that's one long bin for pens or a deep one for offcuts.
The tabs are on the board's 40 mm spacing, so bins sit side by side on the grid. Each cell is one tab, and it takes 6 mm of free board above a bin to drop it in. Add dividers, drainage holes for a sink wall, a label or a pattern in the walls, as you need.
How to print
PLA or PETG, 0.2 mm, 3 walls. Print it standing up, as it hangs, so the hook tabs come out clean on a normal bed.
Free tools for this STL
- STL volume and weight calculatorUpload an STL, 3MF, or OBJ and get its volume, surface area, size, and the filament weight and cost for PLA, PETG, ABS, and more.
- STL viewer onlineOpen STL files in your browser. Measure distances and holes, cut a section, check it is watertight, and see the print weight. No install, nothing uploaded.
- Convert STL to GLBFree STL to GLB converter. Runs in your browser, so the file never leaves your computer. Preview the model, then download the GLB.
- Convert STL to OBJFree STL to OBJ converter. Runs in your browser, so the file never leaves your computer. Preview the model, then download the OBJ.
Questions
- Does it work with the small and large Skadis boards?
- It's built for Skadis's 5 × 15 mm slots, 40 mm apart along a row, as the community libraries measure them. Check it against your own board with a small print first.
- How much weight will it hold?
- That depends on your filament and walls, so we don't quote a number. Add more tab rows and more walls for anything heavy.
- Can I change the size?
- Yes. Sign up free, fork the part and scrub any size. Changing a size never spends a prompt.
- What file do I get?
- STL for the slicer and GLB for the browser. STEP is on Maker and Pro.
More to make
ModelOpenCommunity
IKEA Skådis headphone holder
IKEA Skådis headphone holder: two pegs on 40 mm centres, a 90 mm wide R55 U-cradle with 3 mm walls and 6 mm lips, and an optional side cable hook.
LaserOpenLaser cut
IKEA Skadis tray
A boxy open tray whose two rectangular side walls are hooked brackets for an IKEA Skadis board, with finger-jointed bottom and front and a back wall between…
ModelOpenCommunity
IKEA Skådis shelf
IKEA Skådis pegboard shelf: 160x80x4 plate with two 5 mm mounting holes on 80 mm centres, a 16 mm rear riser, two drop-in J-pegs on 80 mm centres and an opti…
LaserOpenLaser cut
IKEA Skådis organizer tray with dividers
Shorter open tray with dividers, hung on a Skadis board by two hooked side brackets that curve down to a low front.
ModelOpenCommunity
IKEA Skådis cable hook
IKEA Skådis pegboard cable hook with a 4 mm back plate, two drop-in pegs on 40 mm centres, and three 8 mm wide J-hooks in a vertical row 18 mm apart.
LaserOpenLaser cut
IKEA Skådis bin
An open tray on two hooked side brackets that hang on an IKEA Skadis board, with a floor, a front wall and a back wall.